Why Your Psytrance Track Feels Flat (And How I Fix Mine)
Most tracks that feel flat have the same problem. The drums go as they go, the sounds keep coming, and the energy stays on one flat line from the first bar to the breakdown.
I had one of those sessions where everything simply works, so I recorded my whole thought process on the first part of a new track. This is not a tutorial, and I'm not explaining every plugin. It's how I make decisions, and why. Here are the ones that matter most.
Start from the idea, not from the sounds
After so many atmospheric, melodic tracks I wanted something groove-oriented and pumping. So I got out of my usual 140 to 142 zone and pushed the track to 143 BPM.
That one idea decided everything after it: a round kick that is closer to an 808 but still has a click, a plucky bassline, and most of the session spent on the drums and the groove.
A bassline you don't get tired of
For years I was making clicky basslines fully in mono, and after two or three sessions I was always going back to change them. Something was unpleasant and I didn't know what.
My theory: in nature we never hear mids and highs in perfect mono. So now I keep everything below 250 Hz in mono and make only the top of the bassline a little bit stereo. I'm not quite sure why it works, but the ear fatigue is gone and I don't keep coming back to fix the bass.
Protect the groove from your own sounds
When a single shot plays over the kick and bass, it steals the attention. If there are textures and noises between all the strong shots, the groove never gets the attention back.
In this track there are always four bars between the strong single shots. Something happens, it disappears, and the focus goes back to the kick and bass. That's what makes the whole track feel groovier.

Every change needs a reason
Before a big energy jump I love to put the kick and bass on a filter for eight bars and cut the sub. On headphones it's a small change. On a big sound system it's huge.
But the loss needs a cause. So I place the impacts right there: there's a hit, something happened, and the kick and bass lose their sub as a response. Some type of damage. Without the impacts it's good, but it's not effective.
One detail: I add resonance on that filter only after the cutoff passes 150 Hz. If the resonance is already there around 80 Hz, it boosts the low end back and you don't feel that something is missing.

Leave space after the boom
This is the mistake I see most with students. The boom breaks everything apart, and the fill starts right away. It's okay, but the moment is gone before anyone can feel it.
I start the fill about half a bar later. I also cut every delay and reverb tail that is still playing there, because the tails spoil the effect. It's only one bar, but it's enough to breathe in and continue.
The same goes for the whole track. If you don't push the floor down, there's no distance to the ceiling.

An arp instead of a riser
I personally don't like risers that much. They are easy to make and there's nothing beautiful in them. Here I used an arp instead: G, G sharp and D in a five-step cycle, so it runs as a polyrhythm against the groove, with the cutoff opening over time.
It does the same job of building tension, but it's melodic and it's mine. I use it only in the moments before a jump.
Delete what repeats
Listening back, I heard exactly the same part I had 16 bars before. So the whole section went out. Now the track gets to the point faster, and it's way more effective.
Split your energy jumps
I had the open hat and the rides coming in at the same time, and then 16 bars later a new lead with nothing new in the drums. So the plan is: the open hat alone for the first 16 bars, then the rides together with the lead.
That lead has a flanger that I automate by hand from 0 to 100 percent instead of using the LFO, so I decide when the movement starts and when it ends. Now the track keeps evolving, reaches its highest level, and the breakdown is actually deserved.

Punch on the first beat of the cycle
I had a shout on the first bar of a new cycle. Nice character, but it didn't punch. I put a simple percussive impact under it. You almost don't hear it, but it has the low mids and the dynamics the shout was missing.
These hits are what make the energy move like a wave instead of a flat line.
Then I stop
A session and a half, and I close the project. I don't want to over-listen the track and lose what I like about it right now.
Try this on your track
Open the project you're working on and ask:
Is there space between your strong single shots, so the attention goes back to the groove?
Does every filter move and every drop have a cause?
After a boom, is there a moment of silence before the fill?
Is any section repeating what you did 16 bars before?
Do your energy jumps come one by one, or all at once?
Fix one of them today, not all five.
The full 38-minute session is on YouTube.





Comments